Vermeer 604m Manual

Posted on
Vermeer 604m Manual Average ratng: 5,0/5 3988 reviews
  1. Vermeer 604m Service Manual
  2. Vermeer 604m Specs
  3. Vermeer 604m Manual

Cfpinz wrote:Dad has one and a friend had one, both bought new. I've ran Dad's, it is prone to plugging in damp hay. My old L baler is a whole lot better baler than the XL. On another note, the L is also more baler than the 604M that I just bought at the moment!I have a Vermeer 505I and 505M. The secret to these balers baling good is good pickup teeth and the angle set right on the teeth as that is what starts the bale. Once the teeth gets age/use on them you have to reset the angle as they want start a bale as good. If good pickup teeth, the angle properly set any Vermeer open throat baler from the 'I' baler on is boring to operate as they don't miss a bale or plug.

Reset your angle on the teeth on the side of the pickup. Cfpinz wrote:Dad has one and a friend had one, both bought new. I've ran Dad's, it is prone to plugging in damp hay. My old L baler is a whole lot better baler than the XL. On another note, the L is also more baler than the 604M that I just bought at the moment!I have a Vermeer 505I and 505M. The secret to these balers baling good is good pickup teeth and the angle set right on the teeth as that is what starts the bale. Once the teeth gets age/use on them you have to reset the angle as they want start a bale as good.

Vermeer 604m Manual

If good pickup teeth, the angle properly set any Vermeer open throat baler from the 'I' baler on is boring to operate as they don't miss a bale or plug. Reset your angle on the teeth on the side of the pickup.

Does your M have the Mini Rough Top belts? I just ordered a set for mine, it was an early model with the slick belts and I'm hoping that is what's causing my issues. I've jacked the pickup cam settings in both directions to little effect, and done everything else I know to do to a baler other than replace the pickup teeth. I'm hoping to upgrade the pickup teeth to the large diameter ones all the way across the pickup this winter, but don't have time to go tearing into that right now. I'm going to give this thing the benefit of the doubt, but if I can't make it run like my old L I'm going to give one of the green balers a try.

Cfpinz wrote:Dad has one and a friend had one, both bought new. I've ran Dad's, it is prone to plugging in damp hay. My old L baler is a whole lot better baler than the XL.

On another note, the L is also more baler than the 604M that I just bought at the moment!I have a Vermeer 505I and 505M. The secret to these balers baling good is good pickup teeth and the angle set right on the teeth as that is what starts the bale. Once the teeth gets age/use on them you have to reset the angle as they want start a bale as good.

If good pickup teeth, the angle properly set any Vermeer open throat baler from the 'I' baler on is boring to operate as they don't miss a bale or plug. Reset your angle on the teeth on the side of the pickup.

Does your M have the Mini Rough Top belts? I just ordered a set for mine, it was an early model with the slick belts and I'm hoping that is what's causing my issues. I've jacked the pickup cam settings in both directions to little effect, and done everything else I know to do to a baler other than replace the pickup teeth. I'm hoping to upgrade the pickup teeth to the large diameter ones all the way across the pickup this winter, but don't have time to go tearing into that right now. I'm going to give this thing the benefit of the doubt, but if I can't make it run like my old L I'm going to give one of the green balers a try.Yes my 505M has the notched 3 ply belts with the Alligator Belt Lacing, but the 505I doesn't and it bales almost as good. Do you have the books for your baler, if not get the model and serial number and call Vermeer 1-800-829-0051 and they will send the books for free including the Maintenance Manual. It tells you every way to adjust.

Vermeer 604m Service Manual

Your baler should not miss a bale. To make the Cam more aggressive adjust Clockwise, especially if your teeth are getting worn. Make sure the starter roller is turning as a neighbor tried to bale all day and the key was stripped in the cog wheel for the starter roller and it wasn't turning.

It took me about 10 seconds to find his problem. Always start a bale with the windrow in the center. You can also 1-800-829-0051 and ask for the Agri. Division and a baler specialist will call you back to discuss your problem. Pricefarm wrote:Well I bought one hope I like it. I will have to figure out how to use the monitor on it.

Vermeer 604m Specs

The monitor is pretty simple and straight forward. Order the Vermeer manuals also they will register your baler and contact with any upgrades, If the baler start having problems look for bad bearings or something else that puts slack in the belts. Good idea to get the manuals and adjust everything to specs before baling.

Also the larger pickup teeth helps a lot and is recommended by me. Also any after market teeth will fail pretty quickly. Better off in the long run to buy the genuine Vermeer teeth. Jltrent wrote:Yes my 505M has the notched 3 ply belts with the Alligator Belt Lacing, but the 505I doesn't and it bales almost as good.

Do you have the books for your baler, if not get the model and serial number and call Vermeer 1-800-829-0051 and they will send the books for free including the Maintenance Manual. It tells you every way to adjust. Your baler should not miss a bale. To make the Cam more aggressive adjust Clockwise, especially if your teeth are getting worn. Make sure the starter roller is turning as a neighbor tried to bale all day and the key was stripped in the cog wheel for the starter roller and it wasn't turning. It took me about 10 seconds to find his problem.

Always start a bale with the windrow in the center. You can also 1-800-829-0051 and ask for the Agri.

Division and a baler specialist will call you back to discuss your problem. I called and got all the manuals for it back in the fall, Vermeer will send any owner of their equipment a full set of manuals if you call in and register it with them, great company to work with. Also, I took the chain off the starter roller the other night and set the clearance on that roll scraper to.010' though it didn't help matters any.

Vermeer 604m Manual

I don't care for the design of the starter roller in this baler, my old L has a more aggressive one. I'm anxious to try the new belts in it, and will likely replace the smaller diameter teeth in the pickup this fall/winter when I get around to it.

There's no reason this baler shouldn't be as reliable as my old L, anything less and I'm not going to be satisfied with it.